پیوندهای مفید
آمار
| تعداد نشریات | 8 |
| تعداد شماره‌ها | 423 |
| تعداد مقالات | 5,542 |
| تعداد مشاهده مقاله | 6,470,769 |
| تعداد دریافت فایل اصل مقاله | 5,541,659 |
Fatigue Life Evaluation of Single and Two Riveted Coach Peel Joints Using Strain- Life Criteria | ||
| AUT Journal of Mechanical Engineering | ||
| مقاله 10، دوره 3، شماره 2، اسفند 2019، صفحه 229-234 اصل مقاله (2.19 M) | ||
| نوع مقاله: Research Article | ||
| شناسه دیجیتال (DOI): 10.22060/ajme.2019.14541.5731 | ||
| نویسندگان | ||
| Hadi Moslemi؛ Khalil Farhangdoost* ؛ Pedram Zamani | ||
| Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran | ||
| چکیده | ||
| In this paper, experimental investigation was performed to estimate fatigue life of single and double riveted coach peel joints of 2024 aluminum alloy. Load controlled fatigue tests were conducted with load ratio and frequency of 0.1 and 10 Hz, respectively. Failure of the specimens revealed three major modes of folded region fracture (A-type), fracture from edge of the rivet hole (B-type) and mixed mode fracture (A & B). Although all failure modes contributes equally in single riveted joint, mixed mode fracture was observed as dominant mode in two riveted ones. A numerical approach is applied to estimate fatigue life of riveted coach peel joints. Finite element analysis was implemented by ABAQUS as the first step of this approach to estimate stress distribution, stress concentration factor, stress and strain amplitude. Fatigue lives were then calculated using three fatigue life theories of Monson-Hirschberg, Smith-Watson-Topper and Morrow. Finally, good accordance between numerical and experimental results revealed that the finite element approach combined with fatigue life theories is capable for fatigue life prediction. It is concluded that adding a rivet in longitudinal direction to the single riveted coach peel joint decreases the life cycles by increasing the stress concentration factor. Moreover, results of finite element approach showed that Monson-Hirschberg and experimental data has the best agreement in compare with SWT and Morrow. | ||
| کلیدواژه‌ها | ||
| Coach peel joint؛ fatigue life estimation؛ finite element analysis؛ riveted joint؛ strain-life method | ||
| مراجع | ||
|
[1] X. Sun, E.V. Stephens, M.A. Khaleel, Fatigue behaviors of self-piercing rivets joining similar and dissimilar sheet materials, International Journal of Fatigue, 29(2) (2007) 370-386.
[2] D. Li, L. Han, M. Thornton, M. Shergold, Influence of rivet to sheet edge distance on fatigue strength of self-piercing riveted aluminum joints, Materials Science and Engineering A, 558 (2012) 242-252.
[3] P. Zamani, S. Mohajerzadeh, R. Masoudinejad, Kh. Farhangdoost, Numerical investigation on optimizing fatigue life in a lap joint structure, World Academy of Science, Engineering and Technology, International Journal of Civil, Environmental, Structural, Construction and Architectural, 9 (2015) 647-653.
[4] L. Han, M. Thornton, M. Shergold, A comparison of mechanical behavior of self-piercing riveted and resistance spot welded aluminum sheets for the automotive industry, Materials & Design, 31(3) (2010) 1457-1467.
[5] C.P. Fung, J. Smart, Riveted single lap joints. Part 1: Fatigue life prediction, Proceedings of the institution of mechanical engineers, part G (Journal of Aerospace Engineering), 211 (1) (1997) 13-27.
[6] C.P. Fung, J. Smart, Riveted single lap joints. Part 2: A numerical parametric study, Proceedings of the institution of mechanical engineers, part G (Journal of Aerospace Engineering), 211 (2) (1997) 123-128.
[7] G.S. Booth, , C.A. Olivier, , S.A. Westgate, , F. Liebrecht, , S. Braunling, Self piercing riveted joints and resistance spot welded joints in steel and aluminum, In: Proceedings of the International Body Engineering Conference, Detriot, MI; SAE Paper No. 2000-01-2681, 2000.
[8] B. Li, , A. Fatemi, An experimental investigation of deformation and fatigue behavior of coach peel riveted joints, International Journal of Fatigue, 28(1) (2008) 9-18.
[9] M. Mohammadpour, M.H. Kalajahi, R.H.Oskouei, M. Shakouri, Fatigue life estimation of coach peel riveted joints using multi-axial fatigue criteria, Materials & Design, 62 (2014) 327-33.
[10] M. Shariati, H. Hatami, H. Yarahmadi, H.R. Eipakchi, An experimental study on the ratcheting and fatigue behavior of polyacetal under uniaxial cyclic loading, Materials & Design, 34 (2011) 302-312.
[11] M. Shariati, H. Hatami, Experimental study of SS304L cylindrical shell with/without cutout under cyclic axial loading, Theoretical and Applied Fracture Mechanics, 58 (1) (2012), 35-43.
[12] M. Shariati, H. Hatami, H. Torabi, H.R. Epakchi, Experimental and numerical investigations on the ratcheting characteristics of cylindrical shell under cyclic axial loading, Structural Engineering and Mechanics, 44 (6) (2012), 753-762
[13] M. Shariati, H. Hatami, H.R. Eipakchi, H. Yarahmadi, H. Torabi, Experimental and numerical investigations on softening behavior of POM under cyclic strain-controlled loading, Polymer-Plastics Technology and Engineering, 50 (15) (2011), 1576-1582 [14] ASTM E8. Standard test methods for tension testing of metallic materials, ASTM International, (2009). [15] W. Cui, A state-of-the-art review on fatigue life prediction methods for metal structures, Journal of Marine Science and Technology, 7(1) (2002) 43-56.
[16] A. Fatemi, A. Plaseied, A.K. Khosrovaneh, D.Tanner, Application of bi-linear log-log S-N model to strain-controlled fatigue data of aluminum alloys and its effect on life predictions, International Journal of Fatigue, 27(9) (2005) 1040-1050.
[17] K.N. Smith, P. Watson, T.H. Topper, A stress-strain function for the fatigue of metals, Journal of Materials, 5 (1970) 767-778.
[18] A. Ince, G.Glinka, A modification of Morrow and Smith-Watson-Topper mean stress correction models, Fatigue and Fracture of Engineering Materials & Structures, 34(11) (2011) 845-867.
[19] Z. Zhang, Y. Qiao, Q. Sun, C. Li, J. Li, Theoretical estimation to the cyclic strength coefficient and the cyclic strain-hardening exponent for metallic materials: Preliminary study, Journal of Materials Engineering and Performance, 18(3) (2009) 245-254
[20] R.H. Richman, W.P. McNaughton, Correlation of cavitation erosion behavior with mechanical properties of metals, Wear, 140(1) (1990) 63-82. | ||
|
آمار تعداد مشاهده مقاله: 1,209 تعداد دریافت فایل اصل مقاله: 685 |
||