پیوندهای مفید
آمار
| تعداد نشریات | 9 |
| تعداد شمارهها | 446 |
| تعداد مقالات | 5,719 |
| تعداد مشاهده مقاله | 8,018,486 |
| تعداد دریافت فایل اصل مقاله | 6,527,293 |
An Extended Finite Element Method Study on the Effect of Reinforcing Particles on the Fatigue Crack Propagation Behavior of Functionally Graded Plates | ||
| AUT Journal of Mechanical Engineering | ||
| دوره 9، شماره 3، 2025، صفحه 295-316 اصل مقاله (1.13 M) | ||
| نوع مقاله: Research Article | ||
| شناسه دیجیتال (DOI): 10.22060/ajme.2025.23786.6155 | ||
| نویسندگان | ||
| Ehsan Naderi؛ Mohsen Taghizadeh* ؛ Yadollah Alinia | ||
| Department of Mechanical Engineering, Hakim Sabzevari University, Sabzevar, Iran. | ||
| چکیده | ||
| In this work, it is looked into how adding silicon nitride (Si3N4) particles into Functionally Graded Material (FGM) plates affects their resistance to fracture propagation. A comprehensive numerical study is performed using the extended finite element method (XFEM) implemented in the Abaqus software to investigate the impacts of different Si3N4 particle characteristics, including geometry, size, and volume percentage, on the fatigue behavior of FGM plates. The results indicate that these variables have a significant influence on the fracture formation rate and overall fatigue life of the FGM. Specifically, square Si3N4 particles displayed higher efficiency in arresting crack development compared to alternative shapes, which was attributable to their optimal stress distribution. Results show that adding 10, 20, and 30 weight percent of square Si3N4 particles with a side length of 0.89 μm to the FGM increased the fatigue life by 70.47, 57.69, and 53.79 percent, respectively, compared to the case without reinforcing particles. Furthermore, increasing the volume percentage of Si3N4 particles while concurrently reducing their size resulted in a significant gain in both fatigue life and overall strength of the FGM plates. These findings highlight the potential of Si3N4-reinforced FGMs as a highly effective method for reducing fatigue-induced damage and increasing the service life of engineering components. The findings of this study provide useful insights for the design and optimization of FGM-based structures under cyclic loading conditions. | ||
| کلیدواژهها | ||
| Fatigue Failure؛ Functionally Graded Materials؛ Extended Finite Element Method؛ Crack Propagation؛ Fatigue Life | ||
| مراجع | ||
|
[1] I.V. Singh, B. Mishra, S. Bhattacharya, XFEM simulation of cracks, holes and inclusions in functionally graded materials, International Journal of Mechanics and Materials in Design, 7 (2011) 199-218.
[2] S. Bhattacharya, I.V. Singh, B. Mishra, Fatigue-life estimation of functionally graded materials using XFEM, Engineering with computers, 29 (2013) 427-448.
[3] Z. Wang, F. Liu, W. Liang, L. Zhou, Study on tensile properties of nanoreinforced epoxy polymer: macroscopic experiments and nanoscale FEM simulation prediction, Advances in Materials Science and Engineering, 2013 (2013).
[4] S. Bhattacharya, K. Sharma, Fatigue crack growth simulations of FGM plate under cyclic thermal load by XFEM, Procedia Engineering, 86 (2014) 727-731.
[5] M. Zakeri, A. Jafari, Investigation of stress field parameters in a cracked stiffened plate under mixed mode I/II, Aerospace Knowledge and Technology Journal, 5(2) (2016) 93-107.
[6] D. Bartaula, Y. Li, S. Koduru, S. Adeeb, Simulation of fatigue crack growth using XFEM, in: Pressure Vessels and Piping Conference, American Society of Mechanical Engineers, 2020, pp. V003T003A046.
[7] S. Bhattacharya, I. Singh, B. Mishra, T. Bui, Fatigue crack growth simulations of interfacial cracks in bi-layered FGMs using XFEM, Computational Mechanics, 52 (2013) 799-814.
[8] I. Bharti, N. Gupta, K. Gupta, Novel applications of functionally graded nano, optoelectronic and thermoelectric materials, International Journal of Materials, Mechanics and Manufacturing, 1(3) (2013) 221-224.
[9] A. Mohammadi Anari, E. Selahi, Crack initiation and growth simulations of functionally graded dental implant subjected to cyclic axial loads, Fatigue & Fracture of Engineering Materials & Structures, 45(11) (2022) 3123-3136.
[10] A. Shedbale, I.V. Singh, B. Mishra, Nonlinear simulation of an embedded crack in the presence of holes and inclusions by XFEM, Procedia Engineering, 64 (2013) 642-651.
[11] A.P. Singh, A. Tailor, C.S. Tumrate, D. Mishra, Crack growth simulation in a functionally graded material plate with uniformly distributed pores using extended finite element method, Materials Today: Proceedings, 60 (2022) 602-607.
[12] M. Zaidi, K.K. Joshi, A. Shukla, B. Cherinet, A review of the various modelling schemes of unidirectional functionally graded material structures, in: AIP Conference Proceedings, AIP Publishing, 2021.
[13] D. Kaka, R.A. Fatah, P. Gharib, A. Mustafa, Mechanical Properties of Polyester Toughened with Nano-Silica, Iraqi Journal of Industrial Research, 8(3) (2021) 61-68.
[14] A. Ulukoy, M. Topcu, S. Tasgetiren, An Experimental Crack Propagation Analysis of Aluminum Matrix Functionally Graded Material, Advances in Functionally Graded Materials and Structures, (2016).
[15] F. Xu, S. Zhu, J. Zhao, M. Qi, F. Wang, S. Li, Z. Wang, Effect of stress ratio on fatigue crack propagation in a functionally graded metal matrix composite, Composites Science and Technology, 64(12) (2004) 1795-1803.
[16] M. Bhattacharyya, A.N. Kumar, S. Kapuria, Synthesis and characterization of Al/SiC and Ni/Al2O3 functionally graded materials, Materials Science and Engineering: A, 487(1-2) (2008) 524-535.
[17] F. Xu, S. Zhu, J. Zhao, M. Qi, F. Wang, S. Li, Z. Wang, Fatigue crack growth in SiC particulates reinforced Al matrix graded composite, Materials Science and Engineering: A, 360(1-2) (2003) 191-196.
[18] A.P. Agrawal, S.K. Srivastava, Investigations of fatigue crack growth rate behaviour and life prediction of Si3N4/TiB2 reinforced hybrid metal matrix composites, International Journal of Fatigue, 186 (2024) 108373.
[19] A. Lal, N.M. Kulkarni, S. Singh, A. Mahto, R. Kumar, Mixed mode stress intensity factor analysis on edge cracked FGM plate with different material distribution models by XFEM, Journal of Mechanical Science and Technology, (2024) 1-15.
[20] J. Lai, Y. Xia, Z. Huang, B. Liu, M. Mo, J. Yu, Fatigue life prediction method of carbon fiber-reinforced composites, e-Polymers, 24(1) (2024) 20230150.
[21] C. Chiu, V. Prabhakar, S. Tseng, F. Qayyum, S. Guk, C. Chao, U. Prahl, Integrating experimental and numerical analyses for microscale tensile behavior of ceramic particle reinforced TRIP steel composites: a study on local deformation and damage evolution, Composites Part A: Applied Science and Manufacturing, 186 (2024) 108384.
[22] E. Mosayyebi, T.N. Chakherlou, Numerical investigation of patch geometry effect on the fatigue life of aluminum panels containing cracks repaired with CFRP composite patch using XFEM and CZM approach, International Journal of Adhesion and Adhesives, 136 (2025) 103882.
[23] M. Bouchelarm, M. Chafi, A. Boulenouar, N. Benseddiq, Effect of the material gradation on the fracture trajectory in ceramic/metal functionally graded materials, Archives of Metallurgy and Materials, (2024) 955-963-955-963.
[24] A. Karci, V. Erturun, E. Çakir, Y. Çam, Fatigue crack growth rate and propagation mechanisms of SiC particle reinforced Al alloy matrix composites, Aircraft Engineering and Aerospace Technology, 96(2) (2024) 185-192.
[25] J.M. Melenk, I. Babuška, The partition of unity finite element method: basic theory and applications, Computer methods in applied mechanics and engineering, 139(1-4) (1996) 289-314.
[26] T. Belytschko, T. Black, Elastic crack growth in finite elements with minimal remeshing, International journal for numerical methods in engineering, 45(5) (1999) 601-620.
[27] N. Moës, J. Dolbow, T. Belytschko, A finite element method for crack growth without remeshing, International journal for numerical methods in engineering, 46(1) (1999) 131-150.
[28] J.E. Dolbow, An extended finite element method with discontinuous enrichment for applied mechanics, Northwestern university, 1999.
[29] N. Sukumar, N. Moës, B. Moran, T. Belytschko, Extended finite element method for three‐dimensional crack modelling, International journal for numerical methods in engineering, 48(11) (2000) 1549-1570.
[30] M. Stolarska, D.L. Chopp, N. Moës, T. Belytschko, Modelling crack growth by level sets in the extended finite element method, International journal for numerical methods in Engineering, 51(8) (2001) 943-960.
[31] S. Mohammadi, Extended finite element method: for fracture analysis of structures, John Wiley & Sons, 2008.
[32] B. Bourdin, G.A. Francfort, J.-J. Marigo, Numerical experiments in revisited brittle fracture, Journal of the Mechanics and Physics of Solids, 48(4) (2000) 797-826.
[33] W. Lv, B. Ding, K. Zhang, T. Qin, High-Cycle Fatigue Crack Growth in T-Shaped Tubular Joints Based on Extended Finite Element Method, Buildings, 13(11) (2023) 2722.
[34] S. Bhattacharya, I.V. Singh, B. Mishra, Mixed-mode fatigue crack growth analysis of functionally graded materials by XFEM, International Journal of Fracture, 183 (2013) 81-97.
[35] K. Hasikin, N. Soin, F. Ibrahim, Modeling an optical diaphragm for human pulse pressure detection, in: WSEAS International Conference. Proceedings. Mathematics and Computers in Science and Engineering, World Scientific and Engineering Academy and Society, 2009.
[36] G.D. Quinn, J. Salem, I. Bar-On, K. Cho, M. Foley, H. Fang, Fracture toughness of advanced ceramics at room temperature, Journal of research of the National Institute of Standards and Technology, 97(5) (1992) 579. | ||
|
آمار تعداد مشاهده مقاله: 842 تعداد دریافت فایل اصل مقاله: 496 |
||