پیوندهای مفید
آمار
| تعداد نشریات | 7 |
| تعداد شماره‌ها | 399 |
| تعداد مقالات | 5,389 |
| تعداد مشاهده مقاله | 5,287,993 |
| تعداد دریافت فایل اصل مقاله | 4,882,743 |
مطالعه تحلیلی و عددی اثر ضخامت و نوع بتن پوشش بر رفتار دیوارهای برشی فولادی کامپوزیت | ||
| نشریه مهندسی عمران امیرکبیر | ||
| مقاله 2، دوره 53، شماره 9، آذر 1400، صفحه 3623-3648 اصل مقاله (1.36 M) | ||
| نوع مقاله: مقاله پژوهشی | ||
| شناسه دیجیتال (DOI): 10.22060/ceej.2020.17929.6713 | ||
| نویسندگان | ||
| تیمور رحیمی1؛ علی خیرالدین2؛ مجید قلهکی* 3 | ||
| 1دانشجوی کارشناسی ارشد، دانشکده مهندسی عمران، ، دانشگاه سمنان، سمنان، ایران | ||
| 2استاد، دانشکده مهندسی عمران، ، دانشگاه سمنان، سمنان، ایران، | ||
| 3عضو هیات علمی دانشگاه سمنان | ||
| چکیده | ||
| دیوار برشی فولادی کامپوزیت یک سیستم نوین باربر جانبی و متشکل از یک ورق فولادی به همراه پوشش بتن آرمه است که این پوشش به یک سمت یا هر دو سمت آن توسط برش گیرهایی متصل شده است. در دیوار برشی فولادی کامپوزیت، پوشش بتنی مسلح با مهار کردن ورق فولادی و جلوگیری از کمانش آن باعث افزایش ظرفیت برشی دیوار برشی فولادی تا حد تسلیم برش داخل صفحه ورق به جای کشش در راستای میدان کشش قطری می‌شود. هدف از انجام این پژوهش مطالعه تحلیلی و عددی اثر ضخامت و نوع بتن پوشش، بر رفتار دیوارهای برشی فولادی کامپوزیت است. در این مقاله 27 مدل دیوار برشی فولادی کامپوزیت با ضخامت ورق و ضخامت بتن مختلف و نسبت عرض به ارتفاع 0/75، 1 و 1/5 در نرم افزار ABAQUS مدلسازی و با استفاده از تحلیل بار افزون مورد بررسی قرار گرفته است. نتایج حاصل از پژوهش نشان می‌دهد که در تمامی نسبت‌های عرض به ارتفاع برابر 0/75، 1 و1/5 جذب انرژی در مدل‌های دارای ضخامت ورق 6 میلی‌متر از سایر مدل‌ها بیشتر است. نتایج همچنین نشان داد که ضریب رفتار دیوار برشی فولادی کامپوزیت حدود 13/5 برآورد می‌شود. در پایان رابطه‌ی نیمه تجربی برای محاسبه‌ی ضخامت بتن پوشش بر حسب ضخامت ورق فولادی به منظور جلوگیری از کمانش ورق ارائه شده است. | ||
| کلیدواژه‌ها | ||
| دیوار برشی فولادی کامپوزیت؛ ضخامت ورق؛ ضخامت بتن؛ تحلیل بار افزون؛ ضریب رفتار | ||
| موضوعات | ||
| دیوار برشی؛ سازه های جدار نازک؛ سازه های مرکب ( فولادی - بتنی) | ||
| عنوان مقاله [English] | ||
| An Analytical and Numerical Study on Effect of Thickness and Concrete Type of Panels on Behavior of Composite Steel Plate Shear Walls | ||
| نویسندگان [English] | ||
| Teymour Rahimi1؛ ali kheyroddin2؛ | ||
| 1MSc, civil faculty, Semnan university, Semnan, iran | ||
| 2Professor, Department of Civil Engineering, University of Semnan, Semnan, Iran. | ||
| چکیده [English] | ||
| The composite steel plate shear wall (CSPSW) is an innovative lateral load-resisting system that is comprised of reinforced concrete (RC) panels attached to one or both sides of the system using shear connectors. Accordingly, in the CSPSW, the RC panels prevent buckling of the steel plate, and thus, the shear capacity of the plate improves by the shear yielding limit of the plate instead of tension in the direction of the diagonal tension field. Subsequently, this study is aimed to analytically and numerically investigate the effect of thickness and concrete type of panels on the behavior of the CSPSW. To this end, 27 numerical models of CSPSWs with varying thickness of steel plate and concrete panels as well as width-to-height (W/H) ratios of 0.75, 1 and 1.5 have been built using ABAQUS software and then, analyzed through the pushover analysis method. The results indicate that in all W/H ratios, the energy absorption of the models with a plate thickness of 6mm surpasses the others. Importantly, it was found that the response modification factor of the CSPSW is estimated to be 13.5. Lastly, a semi-empirical relationship was proposed to calculate the thickness of the RC panel based on that of the steel plate so that plate buckling could be prevented. | ||
| کلیدواژه‌ها [English] | ||
| Composite Steel Plate Shear Wall (CSPSW), Plate Thickness, Panel Thickness, Pushover Analysis, Modification Factor | ||
|
سایر فایل های مرتبط با مقاله
|
||
| مراجع | ||
|
[1] T.T. Soong, G.F. Dargush, Passive Energy Dissipation Systems in Structural Engineering, Wiley, London, 1997. [2] G.W. Housner, L.A. Bergman, T.K. Caughey, et al., Structural control: past, present and future, J. Eng. Mech. ASCE 123 (9) (1997) 897–971. [3] M. Nakashima, K. Saburi, B. Tsuji, Energy input and dissipation behavior of structures with hysteretic dampers, Earthq. Eng. Struct. Dyn. 25 (5) (1996) 483–496. [4] J. Ericksen, R. Sabelli, A Closer Look at Steel Plate Shear Walls, Modern Steel Construction, USA, 2008 63–67. [5] G. Pachideh, M. Gholhaki, A. Saedi Daryan, Analyzing the damage index of steel plate shear walls using pushover analysis, Structures, 2019, 20, 437-451. [6] M. Gholhaki, G. Pachideh, Investigating of damage indexes results due to presence of shear wall in building with various stories and spans, Int J Rev Life Sci, 2015, 5 (1), 992-997. [7] M. Gholhaki, M. Karimi, G. Pachideh, Investigation of Subpanel Size Effect on Behavior Factor of Stiffened Steel Plate Shear Wall, Journal of Structural and Construction Engineering, 2019, 5 (4), 73-87. [8] M. Gholhaki, G. Pachideh, O. Rezayfar, Sa. Ghazvini, Specification of Response modification factor for Steel Plate Shear Wall by Incremental Dynamic Analysis Method [IDA], Journal of Structural and Construction Engineering, 2019, 6 (2), 211-224. [9] G. Pachideh, M. Gholhaki, M. Shiri, Modeling and Analysis of Thin Steel Plate Shear Walls Using the New Method, 2nd international conference on civil engineering, architecture & urban planning elites, 2016, 2, 124-136. [10] Y. Takahashi, Y. Takamoto, T. Takeda, et al., Experimental study on thin steel shear walls and particular bracing under alternative horizontal loading, IABSE Symposium on Resistance and Ultimate Deformability of Structures Acted on by Well-defined Repeated Loads, Lisbon, Portugal 1973, pp. 185–191. [11] L.J. Thorburn, G.L. Kulak, C.J. Montgomery, Analysis of steel plate shear walls, Structural Engineering Report No. 107, Department of Civil Engineering, University of Alberta, 1983. [12] T.M. Robert, S. Sabouri-Ghomi, Hysteretic characteristics of unstiffened perforated steel plate shear panels, Thin-Walled Struct. 14 (1992) 139–151. [13] V. Caccese, M. Elgaaly, R. Chen, Experimental study of thin steel-plate shear wall under cyclic load, J. Struct. Eng. 119 (2) (1993) 573–587. [14] Q. Zhao, A. Astaneh-Asl, Cyclic behavior of traditional and innovative composite shear walls, J. Struct. Eng. ASCE 130 (2) (2004) 271–284. [15] L. Guo, R. Li, Q. Rong, et al., Cyclic behavior of SPSW and CSPSW in composite frame, Thin-Walled Struct. 51 (2012) 39–52. [16] A. Astaneh-Asl, Seismic behavior and design of composite steel plate shear walls, Steel Tips Report, Structural Steel Educational Council, USA, 2002. [17] AISC, ANSI/AISC 341‐10, Seismic provisions for structural steel buildings, American Institute of Steel Construction, Chicago (IL), 2010. [18] Q. Zhao, A. Astaneh-Asl, Cyclic behavior of traditional and innovative composite shear walls, J. Struct. Eng. ASCE 130 (2004) 271–284. [19] Q. Zhao, A. Astaneh-Asl, Seismic behavior of composite shear wall systems and application of smart structures technology, Steel Struct. 7 (2007) 69–75. [20] Shafaei, S., Ayazi, A. and Farahbod, F., “The effect of concrete panel thickness upon composite steel plate shear walls” J. Constr. Steel Res. 117 (2016) 81-90. [21] A. Yadegari, G. Pachideh, M. Gholhaki, M. Shiri, Seismic Performance of C-PSW, 2nd international conference on civil engineering, architecture & urban planning elites, 2016, 2, 110-123. [22] L. Guo, R. Li, Q. Rong, S. Zhang, Cyclic behavior of SPSW and CSPSW in composite frame, Thin-Walled Struct. 51 (2012) 39–52. [23] Qiuhong, Z. and Astaneh-asl, A. (2004), “Seismic behavior of composite shear wall systems and application of smart structures technology”, 13th World Conference on Earthquake Engineering, Vancouver, Paper No. 2578. [24] Qiuhong, Z. and Astaneh-asl, A. (2007), “Cyclic behavior of traditional and innovative composite shear walls”, Journal of Steel Structures, (2007): 60-75. [25] A. Arabzadeh, M. Soltani, A. Ayazi, Experimental investigation of composite shear walls under shear loadings, Thin-Walled Struct. 49 (2011) 842–854. [26] L. Guo, R. Li, Q. Rong, S. Zhang, Cyclic behavior of SPSW and CSPSW in composite frame, Thin-Walled Struct. 51 (2012) 39–52. [27] A. Rahai, F. Hatami, Evaluation of composite shear wall behavior under cyclic loadings, J. Constr. Steel Res. 65 (2009) 1528-1537. [28] B. Rasouli, S.Shafaei, A. Ayazi, F.Farahbod, “Experimental and Numerical study on steel-concrete composite shear wall using light-weight concrete”, J. Constr. Steel Res. 126 (2016) 117-128. [29] Q. Zhao, A. Astaneh-Asl, Cyclic behavior of traditional and innovative composite shear walls, J. Struct. Eng. ASCE 130 (2004) 271–284. [30] Q. Zhao, A. Astaneh-Asl, Cyclic behavior of traditional and innovative composite shear walls, J. Struct. Eng. ASCE 130 (2004) 271–284. [31] Shafaei, S., Ayazi, A. and Farahbod, F., “The effect of concrete panel thickness upon composite steel plate shear walls” J. Constr. Steel Res. 117 (2016) 81-90. [32] AISC, ANSI/AISC 341-10. Seismic Provisions for Structural Steel Buildings, Chicago (IL): American Institue of Steel Construction, 2010. [33] Q. Zhao, A. Astaneh-Asl, Seismic behavior of composite shear wall systems and application of smart structures technology, Steel Struct. 7 (2007) 69–75. | ||
|
آمار تعداد مشاهده مقاله: 635 تعداد دریافت فایل اصل مقاله: 926 |
||
